This fixes bug #1042, which occured when an RX->OFF->RX sequence
happened quickly enough that the loop in rx_mode() did not see the
change. As a result, the enable_baseband_streaming() call at the start
of that function was not repeated for the new RX operation, so RX
progress stalled.
To solve this, the vendor request handler now increments a sequence
number when it changes the transceiver mode. Instead of the RX loop
checking whether the transceiver mode is still RX, it now checks whether
the current sequence number is the same as when it was started. If not,
there must have been at least one mode change, so the loop exits, and
the main loop starts the necessary loop for the new mode. The same
behaviour is implemented for the TX and sweep loops.
For this approach to be reliable, we must ensure that when deciding
which mode and sequence number to use, we take both values from the same
set_transceiver_mode request.
To achieve this, we briefly disable the USB0 interrupt to stop the
vendor request handler from running whilst reading the mode and sequence
number together. Then the loop dispatch proceeds using those pre-read
values.
This is not currently essential, since the current M4 code will not
trigger an SGPIO interrupt until the offset and tx fields are set.
In future though, we want to explicitly set up the M0 state here.
One of the few instructions that can use the high registers (r8-r14) is
the add instruction, which can add any two registers, as long as one of
them is also used as the destination register.
By using this form of add , we can add buf_base (in a high register) to
the offset within the buffer (in a low register), to get the desired
pointer value (buf_ptr) which we want to access.
This saves one cycle by eliminating the need to move buf_base to a low
register first.
The lsr instruction here shifts the value in r0 right by one bit,
putting the LSB into the carry flag.
By setting the destination register to r1, we can retain the original
unshifted value in r0, and later write this to the INT_CLEAR register in
order to clear all bits that were set.
This saves two cycles by avoiding the need to load an 0xFFFF value to
write to INT_CLEAR.
The effect of the lsr instruction here is to shift the LSB of r0 into
the processor's carry flag. The subsequent bcc instruction ("branch if
carry clear") will then branch if this bit was zero.
The LSB corresponds to the exchange interrupt flag for slice A only. The
other interrupt flag bits are not checked here, contrary to the comment.
Keeping the base address of this structure in a register allows us to
use offsets to load individual fields from it, without needing their
individual addresses.
However, the ldr instruction can only use immediate offsets relative to
the low registers (r0-r7), or the stack pointer (r13).
Low registers are in short supply and are needed for other instructions
which can only use r0-r7, so we use the stack pointer here.
It's safe to do this because we do not use the stack. There are no
function calls, interrupt handlers or push/pop instructions in the M0
code.
This change saves four cycles by eliminating loads of the addresses for
the offset & tx registers, plus a further two by eliminating the need to
stash one of these addresses in r8.
The high registers (r8-r14) cannot be used directly by most of the
instructions in the Cortex-M0 instruction set.
One of the few instructions that can use them is mov, which can use
any pair of registers.
This allows saving two cycles, by replacing two loads (2 cycles each)
with moves (1 cycle each), after stashing the required values in high
registers at startup.
This allows us to use ldr/str with an immediate offset to access the
SGPIO interrupt registers, rather than first having to load a register
with the specific address we want to access.
This change saves a total of 6 cycles, by eliminating two loads (2
cycles each), one of which could be executed twice.
The current code does reads and writes in two chunks: one of
6 words, followed by one of 2.
Instead, use two chunks of 4 words each. This takes the same number of
total cycles, but frees up two registers for other uses.
Note that we can't do things in one chunk, because we'd need eight
registers to hold the data, plus a ninth to hold the buffer pointer. The
ldm/stm instructions can only use the eight low registers, r0-r7.
So we have to use two chunks, and the most register-efficient way to do
that is to use two equal chunks.
Previously this register was reloaded with the same value during each loop.
Initialising it once, outside the loop, saves two cycles.
Note the separation of the loop start ("loop") from the entry point ("main").
Code between these labels will be run once, at startup.
These variables are already placed together; this commit just groups
them into a struct and declares this in a new header.
This commit should not result in any change to the firmware binary.
Only the names of symbols are changed.
This removes the definition of the offset variable,
volatile uint32_t usb_bulk_buffer_offset = 0;
which is actually superfluous. This variable, along with its neighbour
usb_bulk_buffer_tx, is placed explicitly by the linker script. Its type
is defined by the declaration in usb_bulk_buffer.h.
There is no need to define it here, and doing so gives the misleading
impression that its initial value can be changed by modifying this line!
The initialization to zero never actually takes effect, because the
variable is not placed in the .data or .bss sections which are
initialised by the startup code.
The offset and tx variables are both set in set_transceiver_mode
before SGPIO streaming is started, so the M0 code does not use
them uninitialised.
This changes m0_rom_to_ram to read directly from the ROM region, rather
than copying from where .text has been copied to RAM.
Previously the second .text section would be merged with the first one,
so the M0 image would be copied to RAM during `pre_main`. However, on
newer linkers the sections are not merged together so the second .text
section did not get copied to RAM.
fixes#936
Previously, a USB vendor request could interrupt in the middle of
set_freq and make conflicting changes, leaving the HackRF in an
undefined state.
fixes#772
Previously the firmware would re-initialise the bulk endpoints on
every transceiver mode change including a USB data toggle reset,
which could cause the first bulk packet (512-bytes) to be dropped
by the host if the PID no longer matched.
It's not an Si5351C driver thing, but a HackRF thing. Also added a driver function to check if CLKIN signal is valid, and made use of it, instead of opaque register read code.
Perform PortaPack initialization separately from and earlier than UI initialization. Track if PortaPack was detected, provide (mostly useless) pointer if so. Put "weak" declarations into respective headers. Moving #includes around.
