hackrf

History

Jared Boone 314b3cdc7b Don't put MAX2837 into shutdown mode -- powering up takes a bit too long (500us for PLL to stabilize). Will need to revisit, because the MAX2837 chews up significant current (35 to 45mA) when not in shutdown.

Remove excess calls to max2837_start() and max2837_stop().

2013-09-22 11:52:45 -07:00

xapp058

xapp058/ports: Clean up comments and dead code

2013-09-14 18:24:25 -04:00

bitband.c

Fix-ups to copyrights -- missing e-mail address and inconsistent formatting.

2012-10-06 19:14:55 -07:00

bitband.h

Fix-ups to copyrights -- missing e-mail address and inconsistent formatting.

2012-10-06 19:14:55 -07:00

cpld_jtag.c

cpld: Stream CPLD data from host

2013-09-14 18:24:25 -04:00

cpld_jtag.h

cpld: Stream CPLD data from host

2013-09-14 18:24:25 -04:00

fault_handler.c

fault_handler add more info in case of crash.

2013-03-10 14:23:26 +01:00

fault_handler.h

Added fault handler header file, where I've defined the Cortex-M3/M4 SCB using a struct instead of a slew of #defines. This deviates from the libopencm3 method, but is superior in other ways. So, there you go. It's not in libopencm3, it's here.

2012-10-10 13:36:10 -07:00

hackrf_core.c

Remove unused local variable causing a compiler warning.

2013-09-17 22:21:11 -07:00

hackrf_core.h

Add miscellaneous Jawbreaker pins SCU #defines.

2013-09-20 14:19:07 -07:00

LPC4330_M4_rom_to_ram.ld

Break off a chunk of local RAM to serve the M0 processor.

2013-09-20 20:03:24 -07:00

LPC4330_M4.ld

Break off a chunk of local RAM to serve the M0 processor.

2013-09-20 20:03:24 -07:00

Makefile_inc.mk

Adjust Makefile_inc.mk to serve both M0 and M4 targets through the LPC43XX_TARGET variable.

2013-09-20 20:04:28 -07:00

max2837_regs.def

firmware: gain control

2013-05-27 14:01:22 +02:00

max2837.c

Oops, missed a spot where I should've called a MAX2837 mode function.

2013-09-06 23:09:29 -07:00

max2837.h

Add MAX2837 mode set/get functions.

2013-09-06 22:29:57 -07:00

max5864.c

Use new ssp_transfer() function instead of ssp_write().

2012-10-13 16:58:22 -07:00

max5864.h

Fix-ups to copyrights -- missing e-mail address and inconsistent formatting.

2012-10-06 19:14:55 -07:00

README

started firmware directory with some basic stuff

2012-05-21 11:33:46 -06:00

rf_path.c

Don't put MAX2837 into shutdown mode -- powering up takes a bit too long (500us for PLL to stabilize). Will need to revisit, because the MAX2837 chews up significant current (35 to 45mA) when not in shutdown.

2013-09-22 11:52:45 -07:00

rf_path.h

Move files that have no application-specific bits (e.g. USB stack, tuning, and RF path APIs) to ../common/.

2013-09-17 15:10:46 -07:00

rffc5071_regs.def

Fix overflows in shifts, suppress warnings for temporarily unused variables.

2012-09-04 20:08:30 -04:00

rffc5071.c

Extract knowledge of RF path configurations from the RFFC5071 driver.

2013-09-07 12:59:57 -07:00

rffc5071.h

Extract knowledge of RF path configurations from the RFFC5071 driver.

2013-09-07 12:59:57 -07:00

rom_iap.c

Cleanup on xxx_rom_to_ram directory now it contains only makefile, removed redundant .c file from xxx dir.

2013-04-07 18:55:12 +02:00

rom_iap.h

Add host(hackrf_info)/fw(usb_performance) IAP read part id/serial no(to be confirmed).

2013-03-09 11:47:28 +01:00

sgpio.c

Pull out leaky tri-state transceiver_mode value from sgpio_configure(), replace with SGPIO_DIRECTION_* #defines.

2013-09-17 22:29:41 -07:00

sgpio.h

Pull out leaky tri-state transceiver_mode value from sgpio_configure(), replace with SGPIO_DIRECTION_* #defines.

2013-09-17 22:29:41 -07:00

si5351c.c

firmware: enable int mode if div is even integer

2013-06-07 23:10:35 +02:00

si5351c.h

firmware: fix a warning

2013-06-09 09:15:35 -06:00

streaming.c

Factor out USB API for transceiver control into separate files.

2013-09-20 12:54:56 -07:00

streaming.h

Factor out USB API for transceiver control into separate files.

2013-09-20 12:54:56 -07:00

tuning.c

Remove MAX2837_FREQ_NOMINAL_MHZ #define -- it must be updated now that IF is adjustable. So I pushed the calculation directly into the two places it was used.

2013-09-21 20:27:27 -07:00

tuning.h

Move files that have no application-specific bits (e.g. USB stack, tuning, and RF path APIs) to ../common/.

2013-09-17 15:10:46 -07:00

usb_queue.c

Move files that have no application-specific bits (e.g. USB stack, tuning, and RF path APIs) to ../common/.

2013-09-17 15:10:46 -07:00

usb_queue.h

Broke some application-specific USB code into separate files within hackrf_usb/. Hoping I can use them as necessary in other projects, or push them into a library eventually.

2013-09-19 19:51:32 -07:00

usb_request.c

Move files that have no application-specific bits (e.g. USB stack, tuning, and RF path APIs) to ../common/.

2013-09-17 15:10:46 -07:00

usb_request.h

Move files that have no application-specific bits (e.g. USB stack, tuning, and RF path APIs) to ../common/.

2013-09-17 15:10:46 -07:00

usb_standard_request.c

Remove dependencies on application-specific USB descriptors.

2013-09-17 15:13:12 -07:00

usb_standard_request.h

Move files that have no application-specific bits (e.g. USB stack, tuning, and RF path APIs) to ../common/.

2013-09-17 15:10:46 -07:00

usb_type.h

Remove dependencies on application-specific USB descriptors.

2013-09-17 15:13:12 -07:00

usb.c

Move files that have no application-specific bits (e.g. USB stack, tuning, and RF path APIs) to ../common/.

2013-09-17 15:10:46 -07:00

usb.h

Move files that have no application-specific bits (e.g. USB stack, tuning, and RF path APIs) to ../common/.

2013-09-17 15:10:46 -07:00

w25q80bv.c

Cleanup on xxx_rom_to_ram directory now it contains only makefile, removed redundant .c file from xxx dir.

2013-04-07 18:55:12 +02:00

w25q80bv.h

Cleanup on xxx_rom_to_ram directory now it contains only makefile, removed redundant .c file from xxx dir.

2013-04-07 18:55:12 +02:00

README

This directory contains things shared by multiple HackRF firmware
implementations.