Merge branch 'master' of https://github.com/mossmann/hackrf

firmware/common/hackrf_core.h

@@ -94,8 +94,8 @@ extern "C"
 
 /* RFFC5071 GPIO serial interface PinMux */
 #define SCU_MIXER_ENX       (P7_0)  /* GPIO3[8] on P7_0 */
-#define SCU_MIXER_CLK       (P7_1)  /* GPIO3[9] on P7_1 */
+#define SCU_MIXER_SCLK      (P7_1)  /* GPIO3[9] on P7_1 */
-#define SCU_MIXER_DATA      (P7_2)  /* GPIO3[10] on P7_2 */
+#define SCU_MIXER_SDATA     (P7_2)  /* GPIO3[10] on P7_2 */
 
 /* TODO add other Pins */
 
@@ -120,10 +120,10 @@ extern "C"
 #define PIN_CS_AD  (BIT7)  /* GPIO2[7] on P5_7 */
 #define PORT_CS_AD (GPIO2) /* PORT for CS_AD */
 
-#define PIN_MIXER_ENX  (BIT8)  /* GPIO3[8] on P7_0 */
+#define PIN_MIXER_ENX   (BIT8)  /* GPIO3[8] on P7_0 */
-#define PIN_MIXER_CLK  (BIT9)  /* GPIO3[9] on P7_1 */
+#define PIN_MIXER_SCLK  (BIT9)  /* GPIO3[9] on P7_1 */
-#define PIN_MIXER_DATA (BIT10) /* GPIO3[10] on P7_2 */
+#define PIN_MIXER_SDATA (BIT10) /* GPIO3[10] on P7_2 */
-#define PORT_MIXER     (GPIO3) /* PORT for mixer serial interface */
+#define PORT_MIXER      (GPIO3) /* PORT for mixer serial interface */
 
 /* GPIO Input */
 #define PIN_BOOT0   (BIT8)  /* GPIO0[8] on P1_1 */
@@ -146,7 +146,7 @@ extern "C"
 #define BOOT1_STATE ((GPIO0_PIN & PIN_BOOT1)==PIN_BOOT1)
 #define BOOT2_STATE ((GPIO5_PIN & PIN_BOOT2)==PIN_BOOT2)
 #define BOOT3_STATE ((GPIO1_PIN & PIN_BOOT3)==PIN_BOOT3)
-#define MIXER_DATA_STATE ((GPIO3_PIN & PIN_MIXER_DATA)==PIN_MIXER_DATA)
+#define MIXER_SDATA_STATE ((GPIO3_PIN & PIN_MIXER_SDATA)==PIN_MIXER_SDATA)
 
 /* TODO add other Pins */
 #endif

firmware/common/rffc5071.c

@@ -31,15 +31,18 @@ void rffc5071_init(void)
 {
 	/* Configure GPIO pins. */
 	scu_pinmux(SCU_MIXER_ENX, SCU_GPIO_FAST);
-	scu_pinmux(SCU_MIXER_CLK, SCU_GPIO_FAST);
+	scu_pinmux(SCU_MIXER_SCLK, SCU_GPIO_FAST);
-	scu_pinmux(SCU_MIXER_DATA, SCU_GPIO_FAST);
+	scu_pinmux(SCU_MIXER_SDATA, SCU_GPIO_FAST);
 
 	/* Set GPIO pins as outputs. */
-	GPIO3_DIR |= (PIN_MIXER_ENX | PIN_MIXER_CLK | PIN_MIXER_DATA);
+	GPIO3_DIR |= (PIN_MIXER_ENX | PIN_MIXER_SCLK | PIN_MIXER_SDATA);
 
 	/* set to known state */
 	gpio_set(PORT_MIXER, PIN_MIXER_ENX); /* active low */
-	gpio_clear(PORT_MIXER, (PIN_MIXER_CLK | PIN_MIXER_DATA));
+	gpio_clear(PORT_MIXER, (PIN_MIXER_SCLK | PIN_MIXER_SDATA));
+
+	//FIXME no writes until we get reads sorted:
+	return;
 
 	//FIXME hard coded setup, fields not broken out
 	/* initial setup */
@@ -100,7 +103,7 @@ void rffc5071_reg_write(uint8_t reg, uint16_t val)
 
 	/* make sure everything is starting in the correct state */
 	gpio_set(PORT_MIXER, PIN_MIXER_ENX);
-	gpio_clear(PORT_MIXER, (PIN_MIXER_CLK | PIN_MIXER_DATA));
+	gpio_clear(PORT_MIXER, (PIN_MIXER_SCLK | PIN_MIXER_SDATA));
 	serial_delay();
 
 	/* start transaction by bringing ENX low */
@@ -109,16 +112,16 @@ void rffc5071_reg_write(uint8_t reg, uint16_t val)
 
 	while (bits--) {
 		if (data & msb)
-			gpio_set(PORT_MIXER, PIN_MIXER_DATA);
+			gpio_set(PORT_MIXER, PIN_MIXER_SDATA);
 		else
-			gpio_clear(PORT_MIXER, PIN_MIXER_DATA);
+			gpio_clear(PORT_MIXER, PIN_MIXER_SDATA);
 		data <<= 1;
 
 		serial_delay();
-		gpio_set(PORT_MIXER, PIN_MIXER_CLK);
+		gpio_set(PORT_MIXER, PIN_MIXER_SCLK);
 
 		serial_delay();
-		gpio_clear(PORT_MIXER, PIN_MIXER_CLK);
+		gpio_clear(PORT_MIXER, PIN_MIXER_SCLK);
 	}
 
 	serial_delay();
@@ -140,7 +143,7 @@ uint16_t rffc5071_reg_read(uint8_t reg)
 
 	/* make sure everything is starting in the correct state */
 	gpio_set(PORT_MIXER, PIN_MIXER_ENX);
-	gpio_clear(PORT_MIXER, (PIN_MIXER_CLK | PIN_MIXER_DATA));
+	gpio_clear(PORT_MIXER, (PIN_MIXER_SCLK | PIN_MIXER_SDATA));
 	serial_delay();
 
 	/* start transaction by bringing ENX low */
@@ -149,42 +152,42 @@ uint16_t rffc5071_reg_read(uint8_t reg)
 
 	while (bits--) {
 		if (data & msb)
-			gpio_set(PORT_MIXER, PIN_MIXER_DATA);
+			gpio_set(PORT_MIXER, PIN_MIXER_SDATA);
 		else
-			gpio_clear(PORT_MIXER, PIN_MIXER_DATA);
+			gpio_clear(PORT_MIXER, PIN_MIXER_SDATA);
 		data <<= 1;
 
 		serial_delay();
-		gpio_set(PORT_MIXER, PIN_MIXER_CLK);
+		gpio_set(PORT_MIXER, PIN_MIXER_SCLK);
 
 		serial_delay();
-		gpio_clear(PORT_MIXER, PIN_MIXER_CLK);
+		gpio_clear(PORT_MIXER, PIN_MIXER_SCLK);
 	}
 
 	serial_delay();
-	gpio_set(PORT_MIXER, PIN_MIXER_CLK);
+	gpio_set(PORT_MIXER, PIN_MIXER_SCLK);
 
 	serial_delay();
-	gpio_clear(PORT_MIXER, PIN_MIXER_CLK);
+	gpio_clear(PORT_MIXER, PIN_MIXER_SCLK);
 
 	bits = 16;
 	data = 0;
-	/* set DATA line as input */
+	/* set SDATA line as input */
-	GPIO3_DIR &= ~PIN_MIXER_DATA;
+	GPIO3_DIR &= ~PIN_MIXER_SDATA;
 
 	while (bits--) {
 		data <<= 1;
 
 		serial_delay();
-		gpio_set(PORT_MIXER, PIN_MIXER_CLK);
+		gpio_set(PORT_MIXER, PIN_MIXER_SCLK);
 
 		serial_delay();
-		gpio_clear(PORT_MIXER, PIN_MIXER_CLK);
+		gpio_clear(PORT_MIXER, PIN_MIXER_SCLK);
-		if (MIXER_DATA_STATE)
+		if (MIXER_SDATA_STATE)
 			data |= 1;
 	}
-	/* set DATA line as output */
+	/* set SDATA line as output */
-	GPIO3_DIR |= PIN_MIXER_DATA;
+	GPIO3_DIR |= PIN_MIXER_SDATA;
 
 	serial_delay();
 	gpio_set(PORT_MIXER, PIN_MIXER_ENX);

firmware/mixertx/Makefile

@@ -0,0 +1,11 @@
+# Hey Emacs, this is a -*- makefile -*-
+
+BINARY = mixertx
+
+SRC = $(BINARY).c \
+	../common/hackrf_core.c \
+	../common/si5351c.c \
+	../common/max2837.c \
+	../common/rffc5071.c
+
+include ../common/Makefile_inc.mk

firmware/mixertx/README

@@ -0,0 +1,26 @@
+This program activates the MAX2837 transceiver to transmit an unmodulated
+carrier.  It also configures the RFFC5071 to downconvert the carrier to a lower
+frequency.
+
+Required Lemondrop -> Jellybean connections:
+
+SCK:  Lemondrop P3 pin 2 -> Jellybean P9 2
+MOSI: Lemondrop P3 pin 4 -> Jellybean P9 4
+MISO: Lemondrop P3 pin 6 -> Jellybean P9 6
+SSEL: Lemondrop P3 pin 3 -> Jellybean P9 3
+SCL:  Lemondrop P7 pin 3 -> Jellybean P6 pin 3
+SDA:  Lemondrop P7 pin 5 -> Jellybean P6 pin 5
+SDA:  Lemondrop P7 pin 6 -> Jellybean P6 pin 6
+VCC:  Lemondrop P4 pin 2, 4, or 6 -> Jellybean P17 pin 2, 4, or 6
+1V8:  Lemondrop P11 pin 2, 4, or 6 -> Jellybean P16 pin 2, 4, or 6
+GND:  Lemondrop P5 -> Jellybean P13
+
+Required Lollipop -> Jellybean connections:
+GND: Lollipop P8 pin 1, 3, or 5 -> Jellybean P17 pin 1, 3, or 5
+VCC: Lollipop P8 pin 2, 4, or 6 -> Jellybean P17 pin 2, 4, or 6
+ENX: Lollipop P4 pin 5 -> Jellybean P5 pin 2
+SCLK: Lollipop P4 pin 3 -> Jellybean P5 pin 4
+SDATA: Lollipop P4 pin 1 -> Jellybean P5 pin 6
+
+Also RF connectors, and you're on your own to get the RF switches configured
+properly.

firmware/mixertx/mixertx.c

@@ -0,0 +1,89 @@
+/*
+ * Copyright 2012 Michael Ossmann
+ *
+ * This file is part of HackRF.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.  If not, write to
+ * the Free Software Foundation, Inc., 51 Franklin Street,
+ * Boston, MA 02110-1301, USA.
+ */
+
+#include <libopencm3/lpc43xx/gpio.h>
+#include <libopencm3/lpc43xx/scu.h>
+#include <libopencm3/lpc43xx/i2c.h>
+#include <libopencm3/lpc43xx/ssp.h>
+
+#include "hackrf_core.h"
+#include "max2837.h"
+#include "rffc5071.h"
+
+void pin_setup(void)
+{
+	/* Configure SCU Pin Mux as GPIO */
+	scu_pinmux(SCU_PINMUX_LED1, SCU_GPIO_FAST);
+	scu_pinmux(SCU_PINMUX_LED2, SCU_GPIO_FAST);
+	scu_pinmux(SCU_PINMUX_LED3, SCU_GPIO_FAST);
+
+	scu_pinmux(SCU_PINMUX_EN1V8, SCU_GPIO_FAST);
+
+	/* Configure all GPIO as Input (safe state) */
+	GPIO0_DIR = 0;
+	GPIO1_DIR = 0;
+	GPIO2_DIR = 0;
+	GPIO3_DIR = 0;
+	GPIO4_DIR = 0;
+	GPIO5_DIR = 0;
+	GPIO6_DIR = 0;
+	GPIO7_DIR = 0;
+
+	/* Configure GPIO2[1/2/8] (P4_1/2 P6_12) as output. */
+	GPIO2_DIR |= (PIN_LED1|PIN_LED2|PIN_LED3);
+
+	/* GPIO3[6] on P6_10  as output. */
+	GPIO3_DIR |= PIN_EN1V8;
+}
+
+int main(void)
+{
+	const uint32_t freq = 2441000000U;
+
+	pin_setup();
+	gpio_set(PORT_EN1V8, PIN_EN1V8); /* 1V8 on */
+	cpu_clock_init();
+
+	gpio_set(PORT_LED1_3, (PIN_LED1)); /* LED1 on */
+
+	max2837_setup();
+	rffc5071_init();
+	gpio_set(PORT_LED1_3, (PIN_LED2)); /* LED2 on */
+
+	/* FIXME testing serial reads */
+	while (1) {
+		//rffc5071_init();
+		//rffc5071_reg_write(0x7a, 0xf0ca);
+		if (rffc5071_reg_read(0x00) == 0xbefb)
+			gpio_set(PORT_LED1_3, (PIN_LED3)); /* LED3 on */
+		else
+			gpio_clear(PORT_LED1_3, (PIN_LED3)); /* LED3 off */
+	}
+
+	max2837_set_frequency(freq);
+	max2837_start();
+	max2837_tx();
+	gpio_set(PORT_LED1_3, (PIN_LED3)); /* LED3 on */
+	while (1);
+	max2837_stop();
+
+	return 0;
+}